Ultra
Clear Wood Finish
We know you will take pride in the beautiful results you will achieve
from using Last•n•Last ULTRA CLEAR Waterborne Wood Finish.
We have incorporated the latest state-of-the-art coatings technology
to give you a non-yellowing, quick drying product that seals, helps
preserve and enhance the richness of all your important wood pieces,
cabinets and floors. We recommend using the optional HDC4, Product #
52242, when applying this finish on Floors or other high wear projects.
When used over new, previously stained or previously finished wood surfaces,
Last•n•Last ULTRA CLEAR helps resist staining, chipping
and peeling.
RECOMMENDED
USES:
Ultra Clear Wood Finish is recommended for interior woodworks.
TYPICAL
PROPERTIES
Color in Container: Milky white (dries clear)
Solids Content: 30%+/-1
Chemical Resistance: Excellent
VOC: VOC does not exceed 275 grams/liter
Flash Point: 198°F
Sheen Gloss: >80 units @ 60° on wood
Semi-Gloss: 50-60 units @ 60° on wood
Satin: 25-30 units @ 60° on wood
Freeze/Thaw Stability Stable (if frozen, thaw completely before using)
Pot Life: Unlimited in unopened container
Dry Time: 2 hours with good conditions
Clean Up: Water
Application method: Synthetic waterborne applicator and nylon brush
Coverage: 600-800 square feet per gallon
Proper surface preparation is essential to achieve a high quality finish.
Read the MSDS sheet and wear proper protection, which may include gloves,
eye protection, and/or other protective devices.
Surface Preparation:
New Wood Surfaces:
Make several passes with the sandpaper, increasing the paper fineness
with each pass. The final pass before application on Last•n•Last
ULTRA CLEAR Waterborne Wood Finish should be with a #150 grit screen
pad or sandpaper. Do not use steel wool. Remove dust completely by sweeping,
vacuuming and wiping the work surface with a lint free cloth lightly
dampened with water. To seal raw wood we recommend Last•n•Last
100S Commercial Grade Waterborne Wood Floor Sealer or Last•n•Last
Commercial Grade Oil•n•Water Wood Floor sealer. Avoid using
fillers that contain stearate or wax. The work surface and room temperature
should be at least 65°F.
Previously
Finished Wood Surfaces:
Remove old finish in poor condition. If the old finish is shellac or
contains wax or any stearate, regardless of the condition, remove it
completely . Then follow surface preparation for New Wood Surfaces.
If old finish is still sound and good,, screen the work surface with
a #150 screen disc, #180 grit sand paper, maroon pad or similar.
Remove dust completely by sweeping, vacuuming and wiping the work surface
with a lint free cloth lightly dampened with water. Avoid using fillers
that contain stearate or wax. The work surface and room temperature
should be at least 65°F. Two to three coats work best on previously
finished surfaces.
REMEMBER
TO STIR THIS PRODUCT BEFORE AND DURING USE. LET IT STAND FOR 10 MINUTES
AFTER STIRRING.
Application:
Apply in well ventilated area by nylon brush, or synthetic
waterborne applicator at room temperature and not in direct sunlight.
Last•n•Last ULTRA CLEAR Waterborne Wood Finish looks milky
when applied, but will dry to a clear, beautiful finish. Apply the finish
with the grain of the wood, keeping a wet edge as you move across the
surface. Screen the work surface in between coats with any of the following
#150 screen disc, #180 grit sand paper, maroon pad or similar. Remember
to vacuum and tack thoroughly after
screening to remove all dust. Allow minimum of two hours between coats,
or until thoroughly dry. Heavy finish application, high humidity or
lack of airflow will extend drying times. If waiting longer than 24
hours between coats, sanding is recommended. For superior durability
and chemical resistance, we recommend mixing Last•n•Last
HDC4 Catalyst (sold separately) into this product @ the ratio of 4 oz.
per gallon of of Ultra Clear Finish.
Application
over stain:
Last•n•Last ULTRA CLEAR Waterborne Wood Finish
should adhere well to most stain, but a test for adhesion over brands
other than Last•n•Last stain is recommended. Use Last•n•Last
Classic Wood Stain following instruction on label. Allow the stain to
dry a minimum of 24 hours under good conditions. Make sure the stain
is completely dry before applying the finish or sealer.
Drying
Time:
When applied according to directions, and in thin coats, Last•n•Last
ULTRA CLEAR Waterborne Wood Finish should be dry to the touch in 30
minutes. Allow 1 to 2 hours between coats. Heavy finish application,
high humidity or lack of airflow will extend drying times. Last•n•Last
ULTRA CLEAR Waterborne Wood Finish completely cures within 2 weeks.
If used as a floor finish with HDC4 catalyst, please allow the finish
to be fully cured for area rugs or mats to be put down. The floor is
susceptible to scuffing and marring before full cure.
Clean up:
Use water to clean brushes and applicators.
Maintenance:
Last•n•Last ULTRA CLEAR Waterborne Wood Finish
never needs waxing. We recommend Polycare Floor Cleaner as the safe
and effective cleaning product for all polyurethane coated surfaces.
It has a unique soap-free, no rinse formula which will not harm polyurethane
or varnished wood surfaces.