Paint Colors :: MANUFACTURERS :: ABSOLUTE COATINGS :: ABSOLUTE COATINGS 97801 LAST N LAST COMMERCIAL WATERBORNE WOOD FLOOR FINISH GLOSS 275 VOC SIZE:1 GALLON.

    ABSOLUTE COATINGS 97801 LAST N LAST COMMERCIAL WATERBORNE WOOD FLOOR FINISH GLOSS 275 VOC SIZE:1 GALLON.
ABSOLUTE COATINGS 97801 LAST N LAST COMMERCIAL WATERBORNE WOOD FLOOR FINISH GLOSS 275 VOC SIZE:1 GALLON. 

LNL-1500 Commercial Grade Waterborne Wood Floor Finish
LNL-1500 Commercial Wood Floor Finish incorporates Aluminum Oxide, Microban antimicrobial protection, and UV absorbers in a single component non-yellowing urethane finish. Featuring a 15 Year Residential Wear Warranty, LNL1500 will prove superior durability, with the added benefits of low odor, fast dry time and easy cleanup Microban® protection continuously inhibits the growth of bacteria, mold and mildew that can cause stains, odors, and damage the finish on your floor. And because Microban® protection is built into this coating, it will not wash off or wear away for the life of the finish.

RECOMMENDED USES:
Last•n•Last 1500 Wood Floor Finish is recommended for interior residential application.

TYPICAL PROPERTIES
Color in Container: Milky white (Dries clear)
Solids Content: 32+/-1%
Chemical Resistance: Excellent
VOC:VOC does not exceed 275grams/liter
Flash Point 198°F
Sheen Gloss: >80 units @ 60° on wood
Semi-Gloss: 50-60 units @ 60° on wood
Satin: 25-30 units @ 60° on wood
Freeze/Thaw Stability: Stable (if frozen, thaw completely before using)
Pot Life: Unlimited in unopened container
Dry Time: 2 to 3 hours with good conditions
Clean Up: Water
Application method: T- bar applicator, Synthetic waterborne applicator and nylon brush.
Coverage: 400-450 sq. feet per gallon.

Proper surface preparation is essential to achieve a high quality finish. Read the MSDS sheet and wear proper protection, which may include gloves, eye protection, and/or other protective devices.

Surface Preparation:
New or Newly Sanded Floors or Wood Surfaces:Prepare the floor according to NWFA or NOFMA accepted standard. The final pass before application of Last•n•Last 1500 and sealer should be a #150 grit screen pad or sandpaper. Remove dust completely by sweeping, vacuuming and wiping the floor or work surface with a lint free cloth lightly dampened with water. The floor or work surface and room temperature should be at least 65°F.

Previously finished Floors or Wood Surfaces: Remove old finish in poor condition. If the old finish is shellac or contains wax or any stearate, regardless of the condition, remove it completely then follow surface preparation for New Wood Surfaces. If old finish is still sound and good, screen the work surface with a #150 screen disc, #180 grit sand paper, maroon pad or similar. Remove dust completely by sweeping, vacuuming and wiping the work surface with a lint free cloth lightly dampened with water. The work surface and room temperature should be at least 65°F. Two to three coats work best on previously finished surfaces.

REMEMBER TO STIR THIS PRODUCT BEFORE AND DURING USE. LET IT STAND FOR 10 MINUTES AFTER STIRRING.

Application:
Apply in well ventilated area by nylon brush, or synthetic waterborne applicator at room temperature and not in direct sunlight. Last•n•Last 1500 looks milky when applied, but will dry to a clear, beautiful finish. Pou a 6-8” wide line of the finish along the starting wall. Apply the finish with the grain of the wood. Using a clean pre-dampened waterborne applicator, pull forward with the grain of the wood, moving the finish towards the opposite wall. Holding the applicator at a snowplow angle will maintain a wet edge at all times.( Maintain at least 3” wide wet edge to ensure proper coverage). At the end of each run, turn the applicator towards you and pad out the applicator parallel to the wet edge. Feather out turns. If pushed too hard or fast, drips will fly off the applicator. Missed areas can be touched up if seen right away. To prevent lapping and dry marks, be sure you are using the recommend coverage. Do no spread too thin. Screen the work surface in between coats with any of the following #150 screen disc, #180 grit sand paper, maroon pad or similar. Remember to vacuum and tack thoroughly after screening to remove all dust. Allow minimum of two hours between coats, or until thoroughly dry. Heavy finish application, high humidity or lack of airflow will extend drying times. If waiting longer than 24 hours between coats, sanding is recommended.

Application over stain: Last•n•Last 1500 should adhere well to most stain, but a test for adhesion over brands other than Last•n•Last stain is recommended. Use Last•n•Last Classic Wood Stain following instruction on label. Allow the stain to dry a minimum of 24 hours under good conditions. Make sure the stain is completely dry before applying the finish or sealer.

Drying Time:
When applied according to directions, and in thin coats, Last•n•Last 1500 should be dry to the touch in 1 hour. Allow minimum of 2 hours between coats. Heavy finish application, high humidity or lack of airflow will extend drying times. Last•n•Last 1500 completely cures within 2 weeks. Please allow the finish to be fully cured for area rugs or mats to be put down. The floor is susceptible to scuffing and marring before full cure.

Clean up:
Use water to clean brushes and applicators.

Maintenance:
Last•n•Last 1500 never needs waxing. We recommend Polycare Floor Cleaner as the safe and effective cleaning product for all polyurethane coated surfaces. It has a unique soap-free, no rinse formula which will not harm polyurethane or varnished wood surfaces.

 
   

Details
 
SKU: 5149197801
Weight11.00 lbs
Market price: $180.84
Price: $90.42

Options
 
Quantity Out of stock



  50%
 

    Detailed images
ABSOLUTE COATINGS 97801 LAST N LAST COMMERCIAL WATERBORNE WOOD FLOOR FINISH GLOSS 275 VOC SIZE:1 GALLON.

 

    Recommended products list
  • CABOT STAIN 41608 MEDIUM BASE SOLID OIL DECKING STAIN SIZE:QUART.
  • WOOSTER 1123 AMBER FONG VARNISH BRUSH BROWN CHINA BRISTLE SIZE:4" PACK:6 PCS.
  • WOOSTER BR424 LAMB PAD SIZE:5.5" PACK:24 PCS.
  • RUSTOLEUM 77608 7760830 SPRAY PAINT HERITAGE RED SATIN STOPS RUST SIZE:12 OZ. SPRAY PACK:6 PCS.
  • DUMOND CHEMICAL 7005 PEEL AWAY NO. 7 SIZE:5 GALLONS.
  • ZINSSER 05063 FLAT TINTABLE WHITE WATERTITE FLEXIBLE PRIMER AND FINISH SIZE:5 GALLONS.
  • MINWAX 21475 GLOSS AMERICAN CHESTNUT 475 POLYSHADES SIZE:1/2 PINT.
  • 3M 7722 SCOTCH BRITE FLOOR SCRUBS PACK:12 PCS.
  • 3M 10118 1/0 FINE SYNTHETIC STEEL WOOL PACK:18 PCS.
  • 3M 9090NA 4-3/8" X 11" MED DRYWALL SANDING SCREEN 2PK PACK:10 PCS.
  •  
     

     

    Popular Categories

    METALLIC PAINT

    WOOD STAINS

    CONCRETE FLOOR PAINT

    POOL PAINT

    SPRAY PAINT

     

     

     

    Popular Brands

    MODERN MASTERS

    HAMMERITE

    DRYLOK

    CABOT STAIN

     

    ZAR

    MINWAX

     

    Best Seller Products

    Minwax Poly

    Zar Stain

    Danish Oil

    Last N Last

    Roller Cover

    Modern Masters Metallic Paint

    Hammerite Paint

     
     
    We accept major credit cards
    credit cards logo
     
     
    SEO by site SEO
     
     
    CONNECT WITH US
    Copyright 2005-2015 Paint Colors - All Rights Reserved