Gold Oil•n•Water Wood Finish
Ultra Gold incorporates the latest Oil·n·H2O technology
with Microban antimicrobial protection, for advanced protection of all
interion wood surfaces. Our unique Oil·n·H2O, 100% urethane
technology, is incredibly easy to use, and provides beautiful long lasting
protection to all types of wood. Ultra Gold is designed to be used on
all types of wood, including floors, stairs, moldings, furniture, and
crafts. No thinning required. Not recommended for white stained wood.
Microban protection continuously inhibits the growth of bacteria, mold
and mildew that can cause stains, odors,
and damage the finish on your floor. And because Microban protection
is built into this coating, it will not wash off or wear away for the
life of the finish.
LNL Ultra Gold is recommended for interior residential wood.
Color in Container: Yellowish white (Dries clear)
Solids Content: 30+/-1%
Chemical Resistance: Excellent
VOC: VOC does not exceed 275grams/liter
Flash Point: 198°F
Sheen Gloss: >80 units @ 60° on wood
Semi-Gloss: 50-60 units @ 60° on wood
Satin: 25-30 units @ 60° on wood
Freeze/Thaw Stability Stable: (if frozen, thaw completely before using)
Shelf Life: Unlimited in unopened container
Dry Time: 2 hours under good conditions
Clean Up: Water
Application method: Synthetic waterborne applicator and nylon brush.
Coverage: 500-550 sq. feet per gallon.
surface preparation is essential to achieve a high quality finish. Read
the MSDS sheet and wear proper protection, which may include gloves,
eye protection, and/or other protective devices.
New or Newly Sanded Floors or Wood Surfaces:Prepare the floor according
to NWFA or NOFMA accepted standard. The final pass before application
of Last•n•Last Ultra Goldand sealer should be a #100 to
#150 grit screen pad or sandpaper. Remove dust completely by sweeping,
vacuuming and wiping the floor or work surface with a lint free cloth
lightly dampened with water. The floor or work surface and room temperature
should be at least 65°F.
Previously Finished Floors or Wood Surfaces:Remove old finish in poor
condition. If the old finish is shellac or contains wax or any stearate,
regardless of the condition,remove it completely then follow surface
preparation for New Wood Surfaces. If old finish is still sound and
good, screen the work surface with a #100 to #150 screen disc, #180
grit sand paper, maroon pad or similar. Remove dust completely by sweeping,
vacuuming and wiping the work surface with a lint free cloth lightly
dampened with water. The work surface and room temperature should be
at least 65°F.
TO STIR THIS PRODUCT BEFORE AND DURING USE. LET IT STAND FOR 10 MINUTES
Apply Ultra Gold with the grain of the wood using long even strokes.
on Floors: Apply in well ventilated area by nylon brush, or synthetic
waterborne applicator at room temperature and not in direct sunlight.
Slightly dampen applicator with finish prior to starting. Pour finish
onto floor in a 4” strip along the starting wall. Apply finish
with the grain of the wood. Pull the applicator towards you at a slight
“snowplow” angle. Remember to keep a wet edge as you work.
Feather all turns and stops in the direction which the applicator was
pulled. When you reach the end wall, pull the applicator around in a
sweeping motion, without lifting it from the floor. Feather turn, and
gently touch any missed spots. Apply at recommended coverage in thin
over stain: Last•n•Last Ultra Gold should adhere well to
most stain, but a test for adhesion over brands other than Last•n•Last
stain is recommended. Use Last•n•Last Classic Wood Stain
following instruction on label. Allow the stain to dry a minimum of
24 hours under good conditions. Make sure the stain is completely dry
before applying the finish or sealer.
When applied according to directions, and in thin coats, should be dry
to the touch in 1 hour. Allow minimum of 2 hours between coats. Heavy
finish application, high humidity or lack of airflow will extend drying
times. Last•n•Last Ultra Gold completely cures within 2
weeks. Please allow the finish to be fully cured for area rugs or mats
to be put down. The floor is susceptible to scuffing and marring before
full cure.. No more than two coats are recommended per day.
Use water to clean brushes and applicators.
Last•n•Last Ultra Gold never needs waxing. We recommend
Polycare Floor Cleaner as the safe and effective cleaning product for
all polyurethane coated surfaces. It has a unique soap-free, no rinse
formula which will not harm polyurethane or varnished wood surfaces.